What did you do to your FJR today?

[extrememarine]

I never took the time to put heated grips on this '09. It had the v-strom hand guards on it when I got it and I had let that be good enough.

What was up with the grip heaters?

[bungie4]

Yeah, I'm glad Griff got this one back in functioning order becuase I have not seen any good deals on '13's lately...

If Wheaton's valve check had gone any further sideways, it would have ended up in GA.

If he wanted a new FJR, he could just throw another one in the ditch!


Kidding aside, glad you were there Griff to right the ship on the valve check.

Ahem.

[gixxerjasen]

I never took the time to put heated grips on this '09. It had the v-strom hand guards on it when I got it and I had let that be good enough.

What was up with the grip heaters?

Aha, I've been poking at the search function because my stock AE heated grips aren't so warm anymore. Looks like I have some interesting work ahead of me. That said, Texas summer is coming so likely I'll forget about it till I need it again.

[griff]

Yeah, I'm glad Griff got this one back in functioning order becuase I have not seen any good deals on '13's lately...

Ummm, I'll share half the blame and half the credit for gittin er done.

[wheatonFJR]

I recorded the start up with intention of sending it to Wheaton if his valve check went any further side ways so he could remember what a running FJR sounded like. (Hey, I'm just here to help).

If Wheaton's valve check had gone any further sideways, it would have ended up in GA.

Ain't that the fkn truth!

I think Lucky gave it up when you asked me if I had a hammer!

[raYzerman]

I'd have put it back together without doing anything, he rides so slow he wouldn't notice the timing a tooth off........

[wheatonFJR]

I'd have put it back together without doing anything, he rides so slow he wouldn't notice the timing a tooth off........

Who said it was only 1 tooth off? lol

But you ARE right on the rides slow part.

[extrememarine]

At this point, I assumed you put that motor into a snowblower for Line...

Yeah, I'm glad Griff got this one back in functioning order becuase I have not seen any good deals on '13's lately...

Ahem.

I have $100 I'd toss at you for it...

[bungie4]

At this point, I assumed you put that motor into a snowblower for Line...

Yeah, I'm glad Griff got this one back in functioning order becuase I have not seen any good deals on '13's lately...

Ahem.

I have $100 I'd toss at you for it...

Hum.. a 145hp snowblower, i think your onto something.

[wheatonFJR]

I just got back from a 200 mile ride. I ended up near the Beallsville Diner and the SEO roads. The roads are already clean and beautiful.

I like 26, 260, 800, 277, and 556...

Don't forget 255, 536 and the West end of 78

Agreed!

[Festus]

Who said it was only 1 tooth off? lol

But you ARE right on the rides slow part.

It might have been a safety device put in place to protect you

[wheatonFJR]

Who said it was only 1 tooth off? lol

But you ARE right on the rides slow part.

It might have been a safety device put in place to protect you

Yeah, but I could have used that last tooth on that Wheaton pass.

[Canadian FJR]

I picked up a Raptor on my way to Florida.
I’ll try it when I get home.


Canadian FJR

[extrememarine]

Raptor chassis + Bungie's FJR motor = Now we're talkin'...

I picked up a Raptor on my way to Florida.
I’ll try it when I get home.


Canadian FJR

[extrememarine]

Rode it.

There is no substitute for some two-wheel therapy - brisk (temperature wise) 150-ish mile loop this afternoon. It runs, rides, handles as expected - meaning I didn't F anything up...

[bungie4]

I'll be crossing that bridge in a couple of weeks.

[CollingsBob]

I ordered a new neutral switch assembly along with 2 of the allen screws that hold it..$175.43 cdn….

[FJRoss]

I ordered a new neutral switch assembly along with 2 of the allen screws that hold it..$175.43 cdn….

Crap! You would almost think you were buying BMW parts.
I had to replace the neutral switch on my 2007. Seems to me it was maybe $50 at the time. Don't know what the GenIII+ version is like, but the '07 was a wire with a multi pin connector on one end and a block with 5 copper contact "pads" on the other - one for neutral plus one for each gear. (There was a discontinuity inside the block for the neutral wire which couldn't be easily soldered because the wires were potted in epoxy or something)

[CollingsBob]

I ordered a new neutral switch assembly along with 2 of the allen screws that hold it..$175.43 cdn….

Crap! You would almost think you were buying BMW parts.
I had to replace the neutral switch on my 2007. Seems to me it was maybe $50 at the time. Don't know what the GenIII+ version is like, but the '07 was a wire with a multi pin connector on one end and a block with 5 copper contact "pads" on the other - one for neutral plus one for each gear. (There was a discontinuity inside the block for the neutral wire which couldn't be easily soldered because the wires were potted in epoxy or something)

Probably similar…I didn’t shop around, I just called one of the local stealerships and ordered it over the phone..

[raYzerman]

Typical gouging with Canajan prices for OEM parts. The 6 speed one is pricey, but so is the 5 speed switch. Save the old one!! Might be able to clean up the contacts and the plunger..... have to replace the one on my former root beer FJR, I've cleaned it a few times..... but I have a gently used one with 2k miles on it from the '14 engine I put in the '06 project bike. Partzilla price ~U$55 or so.